Description: Hot-End Double Drive Gear made exclusively for the Hephestos 2 with easy-access mechanical PTFE and bag of 5 spare PTFE tubes. 0.4 mm nozzle, for 1.75 mm filament. BOX CONTENTS Box contents 1 x Hot-End with a 40W 12V ceramic cartridge heater and 100K NTC thermistor Connectors adapted to the Hephestos 2 1 x spare-parts bag containing 5 machined PTFE tubes COMPATIBILIDAD Compatibility Hephestos 2
Description: Hot-End Double Drive Gear made exclusively for the Witbox 2 with easy-access mechanical PTFE and bag of 5 spare PTFE tubes. 0.4 mm nozzle, for 1.75 mm filament. BOX CONTENTS Box contents 1 x Hot-End with a 40W 12V ceramic cartridge heater and 100K NTC thermistor Connectors adapted to the Witbox 2 1 x spare-parts bag containing 5 machined PTFE tubes COMPATIBILIDAD Compatibility Witbox 2
LokBuild 3D Print Build Surface **Special TCT Show Price** The LokBuild replaces the need for blue masking tape or polyimide films such as Kapton Tape, the LokBuild 3D Print Build Surface is made from heat-resistant materials to provide a stable build platform for 3D printed models whilst allowing completed models to be removed easily. The LokBuild 3D Print Build Surface is constantly being tested with new materials and it’s currently compatible with the following materials ABS, PLA, HIPS, PET colorFabb_XT, colorFabb nGen, colorFabb_HT, colorFabb XT-CF20 (carbon fibre) Woodfill, Bronzefill, Copperfill, Brassfill Polymaker PC-Plus (polycarbonate), Polymaker PC-Max (polycarbonate), Polymaker PolyFlex, Ninjaflex Features of the LokBuild 3D Print Build Surface: Optimal 3D printing surface Improves model adhesion Reduces warping Easier nozzle height calibration Durable and long lasting Protect your build plate Easy removal of completed prints One build surface for most materials Easily cut to size with scissors or craft knife Easy to install and remove Installing the LokBuild 1.) Wipe down the build platform ensuring it is clean. 2.) Trim LokBuild down to match the shape and size of your own build plate, this can be done very easily with household scissors or a craft knife. 3.) Remove the adhesive backing and apply the LokBuild to the build plate, you should start from one side and work your way to the other side, smoothing the LokBuild as you go. 4.) Adjust the 3D printers nozzle height and check that the build surface is level. Cleaning the LokBuild LokBuild doesn’t need to be cleaned very often, but if you do clean the LokBuild you should use alcohol wipes or similar (low % Isopropyl). Do not use acetone or anything with a high % Isopropyl, this will damage the surface of the LokBuild. Nozzle Height Calibration with the LokBuild LokBuild is more forgiving than other products on the market when setting the nozzle height and doesn’t require such a high level of accuracy. Be aware there will be an optimal nozzle height for your chosen material and printer. The key to a good nozzle height is to experiment, it’s recommended to start further away from the bed than with other surfaces and then reduce the nozzle height slightly until the print sticks to the LokBuild. Because of the wide range of 3D printers and materials it makes it impossible to give exact print parameters, but a good starting point for the nozzle height would be between 0.20mm – 0.25mm.
MK2a Heated Bed Kit Suitable for most 3d printers with a 200 mm x 200 mm bed Products included in the kit: 12V MK2a Heat bed 200 mm x 200 mm 4 x Standard 30.5x4.5x0.45 spring 4 x M3x25 Screw - DIN-912 Class 8.8 Black 4 x M3 Self-locking nut 100K Thermistor 3950 1% with glass encapsulation. 1 m cable with connection for the thermistor. 1.5mm 2 diameter and 1 m long power supply cable for Heat bed. 1.5mm cable tie Soldering will required to attach cables to heated bed A suitable 12V power supply is also required with a rating of at least 10 amps Warning! Before touching it, turning the hotbed off and wait at least 10 minutes. It may still be hot after turning it off. Do not leave unattended while functioning. Keep away from children.
3D PRINTING 3D printers are fantastic things! Producing some great looking parts straight off the printer. However, if you actually own a desktop 3D printer you will know that this isn't always the case and all kinds of printing errors can creep in. Removing support material can sometimes be a pain and what if you need to modify the part after printing? You won't want to print the whole thing again if it can be avoided!... This is where the MODIFI3D Finishing Tool steps in. MODIFI3D offers a low cost solution to Finish, Repair and Modify 3D printed parts. WHAT IS MODIFI3D? MODIFI3D is a heated tool with specially coated interchangeable tips designed to finish, repair and modify 3D printed parts. MODIFI3D Is designed to replace much of the sanding, scraping and snapping to finish off your 3D prints. The pen like form of MODIFI3D makes it very comfortable to use and extremely easy to control when precision is important. MODIFI3D works with PLA, ABS and other 3D printing materials. See the... 4 Interchangeable Tips . MODIFI3D FEATURES 4 interchangeable tips - Needle, knife, scoop and point tips. Special tip coating to prevent sticking. Rapid heat up in less than 15 seconds. Sleep mode if not used for 25 seconds. Lightweight, compact and easy to use. Touch switch and indicator light. USB powered (USB 2.0 or USB 3.0). Basic stand included. MODIFI3D SPECS 5V 8W USB 2.0 or USB 3.0 recommended Size: 15mm (0.6") x 117mm (4.6") excluding tips Weight: 120g (4.3 oz) Cable: 1.5m (59") long to USB A plug Heats up to 300ºC (572ºF) in less than 15 seconds. Maximum temperature of 420-450ºC (788-842ºF) Video can be found here